Water Proofing Solutions
TS 101 – Liquid integrated waterproofer
TS 103 – A high range water reducing super plasticising admixture
TS 201 Primer - Universal primer for waterproof coatings
TS 202 - Flexible protective polymer
TS 204 - Acrylic cementitious flexible waterproof coating
TS 205 SPR - Decorative, Elastomeric , Waterproof protective coating
TS 206 EMB - Flexible bitumen based membrane
TS 301 - Adhesive for fixing of ceramics tiles
TS 3000 - A unique way to treat irregular joints
TS 101 – Liquid Integrated Waterproofer
Description
A liquid admixture for concrete to give high water resistance based upon a blend of surface-active agents and refined lingo-sulphonate. Waterproof concrete is the result of good concrete practice coupled with low w/c ratio compatible with achieving full compaction. The use of TS 101 enables all these criteria to be met due to its strong plasticizing and water reducing properties.
Primary Uses
TS 101 should be used in all structural concrete that is constantly or intermittently in contact with water such as sea walls, tunnels, basements, structural and pre-cast concrete in exposed superstructures.
Advantages
Concrete containing TS 101 is resistant to water penetration either under conditions of hydrostatic pressure or capillary absorption.
Durability is increased due to a significant reduction in w/c ratio.
The cohesive properties of the concrete are improved thus reducing segregation and bleeding.
The use in cement mortar gives excellent water proofing qualities and it is recommended to use in cement mortar renderings in brick bat coba and box type treatment for stone fixing.
The surface finish of the concrete is improved.
Standards
ASTM C494: Types A & D.
IS: 2645.1991
Directions for Use
TS 101 should be added to the concrete mix/ cement mortar during the mixing cycle at the same time as the water and the aggregates. Never add TS 101 to the dry cement.
Dosage
Field trials should be conducted to determine the optimum addition rates of TS 101. A dosage range of 250ml per 50kg of cement is recommended as a starting point.
Effects of over dosage
A severe over-dosage of TS 101 will result in the following:
Retardation of initial set.
Increase in air entrainment.
Increase in workability.
Packaging
TS 101 is available in 1, 5, 10, 25, 50, 100 & 200 Ltr drums
Composition
A blend of specially selected surface-active agents and refined lignosulphonates.
Points to remember when producing waterproof concrete:
Ensure specified water/cement ratio is not exceeded
Keep water content as low as possible compatible with achieving
full compaction.
Place concrete quickly and ensure it is thoroughly compacted.
Protect new concrete against rapid drying out and ensure
adequate and complete curing with our PROTEKT IT 601 curing
compounds.
Action
TS 101 assists in the production of water resistant concrete by its two fold action:
I. It significantly reduces water demand to enable production of good workability concrete with a Minimum water/cement ratio.
II. It disrupts the cellular network within the concrete mass (capillaries) that are normally inter-connected thereby reducing the concrete permeability.
Technical Data/Typical properties
Colour: Brown liquid
Specific gravity: 1.12-1.14 at 25°C.
Air entrainment: 2 ± 1% according to grading of sand and water content.
Chloride content: Nil
Special features
Advantage of TS 101‘s strong plasticizing action must be taken to reduce water contents to a minimum. A reduction in w/c ratio in the region of 10 to 15% can generally be achieved.
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labor involved in the application are beyond our control.
TS 103 – A HIGH RANGE WATER REDUCING SUPER PLASTICISING ADMIXTURE
Description
TS 103 is a liquid admixture for concrete based on sulphonated naphthalene. The product may be used to effect substantial water reductions or to produce concrete with normal setting times.
Primary uses
• Production of self-compacting concrete.
• Precast concrete.
• Low water/cement ratio concrete.
• In complicated formwork or with congested reinforcement.
Advantages
• Powerful-plasticizing action reduces or eliminates the need for compaction.
• Concretes of similar workability can be produced with 20-30% less water.
• Increased compressive, tensile and flexural strength can be achieved as a benefit of its water reducing properties.
• High early strengths can significantly increase mould utilization in precast works.
Standards
ASTM C494 Type F
IS 9103:1999
Directions for Use
TS 103 should be added to the mix with the gauging water. No extension to the mixing time is necessary. Never add TS 103 to dry cement. When using TS 103 to produce flowing concrete at site using ready mix trucks, it can be added to the concrete via the feed hopper at the rear of the truck.
Dosage
Field trials should be conducted to determine the optimum addition rates of TS 101. A dosage range of 250ml per 50kg of cement is recommended as a starting point.
Dosage Rate
It is beneficial to evaluate TS 103 by field trials, but as a general guide, to produce concrete, an addition rate of 250 – 300 ml per 50kg of cement is usually sufficient to give the desired result. However, up to three times this amount may be required depending on mix design. Dosage rates will increase in low w/c ratio concrete and concrete where temperatures are high.
Effects of over dosage
A severe over-dosage of TS 103 will result in the following:
• Retardation of initial and final set.
• Slight increase in air entrainment.
• Increase in workability.
Technical Data/Typical properties:
Colour: Dark brown/black
Specific gravity: 1.150-1.160 at 25° C.
pH 7 to 8.
Chloride content: Nil
Packaging
TS 103 is available in 1, 5, 10, 25, 50, 100, 200 Liter drums.
Storage
TS 103 must be stored in a place where temperature does not drop below +5°C. If product has frozen, thaw at +5°C and agitate until completely reconstituted. Store under cover, out of direct sunlight and protect from extremes of temperature. Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Special features
Advantage of TS 101‘s strong plasticizing action must be taken to reduce water contents to a minimum. A reduction in w/c ratio in the region of 10 to 15% can generally be achieved.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 201 PRIMER - UNIVERSAL PRIMER FOR WATERPROOF COATINGS
Description
TS 201 PRIMER is a deep impregnating primer designed by blending special grade of polymers with synthetic binders. It’s deep impregnating action and low viscosity helps it to attain better bonding with highly porous cementitious substrate.
Primary uses
TS 201 PRIMER is best suitable when used as a primer coat after surface preparations for all types of waterproof coatings. It can also be used as a dust proofer and floor sealer for dust proofing purposes
Advantages
TS 201 PRIMER provides the following beneficial properties:
• Helps in sealing all dust and loose particles when used as a primer.
• Can be used as a dust proofer / sealer.
• Can act as a good primer / bond coat for all type of waterproof coatings.
• Has very good bonding with all cementitious substrate.
• Enhances coverage of overcoats.
• Economical and easy to use.
Coverage
TS 201 PRIMER will give a coverage of 6 -7 sq mt. / Liter / coat
Instructions for Use Surface Preparation
Concrete, mortar and masonry surface must be clean, free from grease, oil and loosely adhering particles. All surface must be as true and flat as possible. Efficient surface preparation is essential to achieve high adhesive quality of the product.
Application Method
Apply TS 201 PRIMER over the prepared surface using a brush, squeeze or broom. One coat is normally sufficient. Highly porous substrate may require two coat application. After the coat of TS 201 PRIMER the surface is ready for further top coats.
Technical Data
Form: Liquid
Type: Special polymers blended with synthetic binders
Sp. Gravity: Approx 1.03 kg. / Ltr.
Shelf Life: One year when unopened
Colour: Pink/ green/ grey. Will turn colourless on drying.
Drying time: 2-3 hours
Packing
TS 201 PRIMER is available in 1, 5, 10, 25 , 50 ,100, 200 Liters drum.
Storage:
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 202 - FLEXIBLE PROTECTIVE POLYMER
Description
TS 202 is a pure acrylic based polymer for making a cement based polymer modified waterproofing slurry coating. It is applied to concrete and mortar structures to prevent water infiltration and dampness.
Uses
TS 202 is used for external and internal waterproofing, damp proofing, hairline crack sealing, and protection from chloride in the following structures:
• Water - tanks
• Basements
• Terraces and balconies
• Bridges
• Retaining Walls
• Small Flat Roofs
Advantages
TS 202 provides the following beneficial properties:
• Easy to apply by brush, slurry consistency
• Good adhesion to sound & prepared substrates
• Good abrasion resistant
• Protects against water penetration, salt & carbonation
• Non-toxic when cured, suitable for contact with drinking water
• Slightly flexible
Direction for Use Surface Preparation
Concrete, mortar and masonry surface must be clean, free from grease, oil and loosely adhering particles. Steel and iron surfaces must be free from scale, rust, grease and oil. All surface must be as true and flat as possible. Saturate absorbent surface thoroughly. Efficient surface preparation is essential to achieve high adhesive quality of the product.
Mixing
Mix TS 202 Portland cement in the ratio of 1 PART TS 202 WITH ½ PARTS WATER AND 3 PARTS OF ORDINARY PORTLAND CEMENT to make the waterproof slurry using slow speed mixer. At one time small quantity of material should be mixed to avoid wastage.
Application
Prime the prepared surface with TS 201 PRIMER (WATERPROOF PRIMER) with brush. Apply the first coat of prepared slurry and reinforce with non woven fabric for best results. After the first coat is dried apply the second coat after an interval of 4-6 hours. Third coat can be applied if surface is weak or porous.
Coverage
Depending on type of application, 2 coats are always required. PROTEKT IT 220 gives a coverage of 4 Sqmt. / Kg. / Coat as per mixing instructions. Normally two coats should be applied. In extreme cases three coats may be required.
Curing
As with all cement based products, curing is important. Protect the freshly applied product against direct sunlight and strong winds. Use damp hessian or polythene to aid curing, for 3 days. Then allow to dry out.
Technical Data
Form: Liquid
Type: Synthetic Dispersion
Sp. Gravity: Approx 1.10 kg. / Lit.
Shelf Life: One year when unopened
Packaging: 1, 5, 10, 25, 50, 100 and 200 kg
Storage Condition: Protect from direct sunlight
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 204 - ACRYLIC CEMENTITIOUS FLEXIBLE WATERPROOF COATING
Description
TS 204 is a two component acrylic modified cementitious coating that requires only on site mixing forming the ideal product to waterproof and resurface concrete, masonry, and most other construction materials. Simply applied by stiff brush, roller, or trowel, it forms a waterproof, flexible coating. TS 204 provides an effective barrier to waterborne salts and atmospheric gases. Fluid applied, TS 204 provides a hardwearing, seamless, waterproof membrane for roofs and foundation protection.
Primary uses
• To reface and even out variations in concrete surfaces.
• As a waterproof lining for water retaining structures.
• Sealing and coating tie bar holes to ensure water tightness.
• To provide foundation protection.
• As a waterproof coating for roofs.
• As a backing to marble and granite to prevent water ingress and thus alleviate surface staining.
• To provide protection to concrete surfaces from carbonation and chloride attack.
Advantages
• A 1mm coating provides anti carbonation cover equivalent to over 80cm of concrete.
• Waterproof-resists up to 7 Bars (70 meter head) of pressure.
• Excellent adhesion. Bonds to porous and non-porous surfaces.
• Flexible.
• Non toxic suitable for contact with potable water.
• Suitable for light pedestrian traffic.
• Breathable - whilst repelling water, allows substrate to breathe.
• High resistance to carbon dioxide and chloride ion diffusion.
• Unlike conventional coatings which require a 7-28 day cure of concrete, TS 204 can be applied to 24 hour-old concrete thereby giving immediate protection.
Standards
BS 1881 Part 5 1983 - I.S.A.T.
Technical Data/Typical properties
Density: 1800kg/m³
Water penetration (DIN 1048): 7 bars - no leakage (2mm dft) % elongation: >5% (unbounded)
Surface preparation
As with all coating systems, surface preparation is of prime importance. Remove all grease, oil, dust, residual curing compound, mould release agent or other contaminant that could impair adhesion. Laitance should preferably be removed by light sweep blasting or hydro jetting. Mechanical wire brushing may be appropriate for small areas.
Mixing
TS 204 is supplied in premeasured units and should be mixed on site utilising clean containers. Slowly add the powder to the liquid and mix, using a slow speed drill fitted with a suitable paddle.
Coverage
A Pack of TS 204 will cover approx. 10-12 sq mt / pack / two coats depending upon the porosity of the surface.
Application
Do not apply to dry concrete. Saturate concrete surfaces with clean water whilst still visibly damp, but free of standing water, apply, using a short, stiff bristle brush or roller. Trowel application can be undertaken as necessary. For heavy 6-10mm depressions, honeycombs etc. use less gauging liquid and mix to the desired consistency. Where more than one coat is found necessary to achieve the desired thickness, apply the second or subsequent coats after the previous coat has dried. It is recommended, for general resurfacing, that each coat should be a minimum of 500 – 600 microns thick.
Packaging
TS 204 is supplied in 2 components as below:
Powder (White/Grey colour) - 10 kg bag
Liquid – 5 kg pail
Mixing ratio, liquid to powder, 1:2 by weight
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 205 SPR - DECORATIVE, ELASTOMERIC, WATERPROOF PROTECTIVE COATING
Description
TS 205 SPR is a flexible, elastomeric coating based on acrylic co-polymers. Applied as a liquid, it cures to form a durable, protective, waterproof membrane. It is a single component emulsion containing inert pigments and has a brush able consistency.
TS 205 SPR exceeds all the requirements of a coating that resists carbonation and prevents chloride ion ingress.
Primary uses
TS 205 SPR is designed for the protection of concrete structures against carbonation and chloride ingress. The product is also suitable as a seamless and elastomeric waterproofing coating for timber, asbestos / fiber cement and zinc sheets, asphalt, built-up felt and tiles.
Areas of application
• Bridge, Roof decks, walls etc.
• Concrete repairs.
• Commercial buildings.
• Industrial buildings.
• Waterproofing a variety of substrates.
Advantages
• Easily applied by roller, brush or airless spray.
• Flexible - capable of bridging cracks.
• Protective - barrier against salts and atmospheric gases.
• High-build - masking imperfections in substrates.
• Waterproof - protects concrete from waterborne salts.
• U.V. stable - maintains its appearance.
Directions for use
TS 205 SPR can be applied by brush, roller.
Surface preparation : concrete
All concrete surfaces should be treated to achieve a sound, clean surface free from laitance, oil, grease, mould release agent, residual curing compound, dust or other contaminants that could impair adhesion.
Filler/scrape coat
Surface depressions, blow holes, aggregate pop-outs etc., should be rectified with TS 202 mixed with cement and sand. The filler addition rate being dependent on surface and ambient conditions. The mixed filler is tightly scraped onto the surface to be over coated, paying particular attention to ensure blemishes are filled.
Technical Data/Typical properties
Relative density: 1.25 at 25°C
Application temperature: 5°C to 45°C
Chemical resistance: resistant to spillage of gasoline, diesel, sewage, weak acids and alkalis
Elongation: >100%
Colour: white
Application
TS 205 SPR should be applied to prepared surface in two coats, the first being allowed to dry, before the second is applied. In hot dry climates, application will be assisted by dampening brushes. Where the roof is in poor condition, or where substantial movement is expected in the roof structure, apply a sandwich system incorporating reinforcing fabric. In this application, the fabric is bedded into the wet film of the first coat of TS 205 SPR using a charged brush. Ensure that full contact is achieved and there is no air entrapped. Apply a second coat of TS 205 SPR when the first has dried, at right angles to the first.
Limitations
TS 205 SPR is not resistant to rain until the film has dried. This may take less than 30 minutes in hot dry climates and up to 24 hours in temperate humid conditions. Generally the product should not be applied in rain or if rain is forecast. Similarly, TS 205 SPR will freeze in its wet state so should not be applied to frozen substrates or when the temperature is below 5°C or likely to fall during application.
Packaging
TS 205 SPR is available in 1, 5, 10, 25 and 50Kg. Pails.
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 206 EMB - FLEXIBLE BITUMEN BASED MEMBRANE
Description
TS 206 EMB is a ready to use bitumen based emulsion, protective and waterproof coating. It is a high performance coating that dries to a tough, impermeable waterproof membrane.
Primary Use
• Easy and direct (cold applied) application, no pre heating required.
• Provides an impervious waterproofing membrane that protects concrete structure and brick foundations against chloride and sulphate ions present in soils and water.
• Corrosion resistant and vapor barrier.
Advantages
• Useful as protective coating on concrete and brick foundations, retaining walls, timber, metals, etc.
• Provides a sandwich membrane in new construction and surface treatment on existing slabs.
• Damp – proofing of regular surfaces like concrete and asbestos.
• Provides a key for plaster on difficult surfaces.
• For waterproofing and protection of structure, concrete, columns and beams.
Technical Data/Typical Properties
Specific Gravity: 1 to 1.03
Solids Content by Weight: 62.5%
COLOR: Black
Softening Point: Up to 100 deg. Cent. If exposed to direct sunlight.
Flash Point: 1150 C.
Tensile Strength: 230 psi [ultimate strength can be increased up to 3 times by fiber reinforcement]
Tensile Set Recovery: 95% Adhesion to Mortar: 2700 n/m
Water Permeability: Confirms the norms of IS: 2645 Low Temp. Flexibility: No cracks,
Elongation %: 350-400
Application Instructions
Surface Preparations
The application surface must be clean and free from dust grease and loose particles. Surface may be damp but not saturated.
Application
Apply one coat of TS 201 PRIMER, universal deep impregnating primer, on well- prepared surface. TS 206 EMB should be stirred well before use. It is recommended that 1 – 2 coats should be applied depending upon the degree of protection required after the primer coat. TS 206 EMB can be applied by brush, roller or sprayer. Successive coats of TS 206 EMB should be applied after a minimum of 3-4 hours of the previous applied coat. TS 206 EMB could be diluted up to 15 – 25 % for base and top coats to make the material workable and get the desired coverage.
Limitations
TS 206 EMB is not resistant to rain until the film has dried. This may take less than 45 minutes in hot dry climates and up to 12 hours in temperate humid conditions. Generally the product should not be applied in rain or if rain is forecast.
Similarly, TS 206 EMB will freeze in its wet state so should not be applied to frozen substrates or when the temperature is below 5°C or likely to fall during application.
Coverage
Concrete Surface: 4 Sq mt./Kg./Coat (Depending on the porosity of the surface)
Cleaning
Tools and equipments can be cleaned with pure water.
Packing
TS 206 EMB is available in 1, 5, 10, 25 and 50 Kg Pails.
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 301 - ADHESIVE FOR FIXING OF CERAMICS TILES
Description
TS 301 is a cementitious powder formulated as an adhesive for a wide range of applications.
Mixing instructions
Add TS 301 to cool, clean water at the following rates:
By weight 5:1, Volume 2.5:1. Mix to a uniform lump free consistency and allow standing for 5 minutes before use.
Primary uses
Ceramic wall and floor tiles, terrazzo, quarry tiles and stone cladding in interior and external applications. TS 301 may be employed with confidence in institutional or high traffic conditions. TS 301 is suitable for use in kitchens, showers and wet process areas. For swimming pools, fountains, wet storage vessels and conditions of permanent submersion use TS 301.
Application instructions
Apply TS 301 to a uniform thickness of 3 to 6mm or sufficient to cover the studs or keys on the tile back; on a working area of not more than 1 m². Solid bed fixing is recommended for all horizontal applications and for ceramic, quarry, terrazzo and marble flooring tiles, and vertical heavy duty applications including artificial stone cladding. If preferred, TS 301 can additionally be buttered on the backs of the tiles to ensure full adhesive contact. For all other vertical applications the adhesive bed should be combed horizontally with a notched trowel to remove excess.
Advantages
• Interior or exterior use.
• Water resistant.
• Precision made.
• Easy to use.
• Economical.
• For walls and floors Tiles should be dry and fixed by pressing into place with slight wristing motion, ensuring the tile back achieves full contact with the adhesive.
• High adhesive bond strength.
• Long open time.
• Slip resistant. Ceramic tiles should never be butt jointed. Leave a minimum of 2mm around tiles.
Direction for use
Adjustments to tiles should only be made during the adhesives open time.
Surface preparation
All surfaces must be clean, dimensionally stable, sound and free from all traces of oil, grease, mould release agent and curing compound. TS 301 may be used as a thin section render to even out irregularities in the substrate to a maximum depth of 12mm. This must be conducted as a separate operation; the TS 301 render permitted to cure adequately before tiling commences. Concrete, screeds, renders, and blockwork should be cured sufficiently that all shrinkage movement has occurred. Remove excess adhesive from the face of the tile with a damp sponge or cloth before it sets. Similarly, joints must be raked out in readiness for grouting. Leave for a minimum of 24 hours before grouting. Select the appropriate grout for joint size and in service use from the PROTEKT IT range.
Technical Data/Typical properties
Colour: Grey
Bulk density: 2.0
Plastic density: 1.85
Packaging
TS 301 is available in 25 Kg bags.
Storage
Store under cover, out of direct sunlight and protect from extremes of temperature. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
Note
Field service, where provided, does not constitute supervisory responsibility. For additional information contact your local FUSION representative. FUSION reserves the right to have the true cause of any difficulty determined by accepted test methods.
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
TS 3000 - A UNIQUE WAY TO TREAT IRREGULAR JOINTS
Description
TS 3000 joint sealing system consists of two Products.
The TS 3000 is a highly elastic, rot-proof and chemically resistant sealing.
Membrane
SEALER111 is a single part epoxy compound, which establishes a strong bond to various type pf substrates.
Fields of application:
Sealing of construction joints, expansion joints, connecting joints, cracks and crevices, etc. Adheres to many types of substrates such as concrete, mortar, plasterwork, steel iron, aluminum, stoneware, glass and epoxy. Typical uses are for concrete tanks, cast and cement-pipe connections, bridge decks, tunnels, water towers and reservoirs, ponds, silos, containers, secondary tanks.
TS 3000 can be applied on dry or slightly humid substrates. It is ideal for joint flanks. TS 3000 is Black Colour, weather and waterproof.
Benefits
• Durable
• Long lasting elasticity, even at low temperature
• Root resistant
• Resistant to a wide range of chemicals
• Cost effective
• Approved for use with potable water
• Easy to apply
• Can be applied horizontally, vertically and even Overhead.
Typical properties
Hardness A (ASTMD2240): 65+/- 10 Sh A
Tensile strength: 90 Kg /cm2
Elongation at break: 300 %
Abrasion Resistant (max.): 250 mm3
Accelerated weathering: No cracks
Tear Resistance (Angular): 30
UV resistance: No tears
Resistance to micro-organisms: Resistant
Water absorption (internal H&S method): Very low absorption
Heat ageing: 5% for 1mm thickness
3% for 2mm thickness:
Range of joint treatment: 25mm to 400mm width
Brittleness Temperature: - 450C.
Application
Surface preparation:
Contact surfaces must be clean and free from dust, grease, Water, oil, and other contaminants impairing adhesion. Concrete should be at least 4 weeks old. In order to provide maximum adhesion, concrete surfaces should be mechanically abraded.
Shake adhesive thoroughly, following the guidelines of the manufacturer. Apply the well-mixed Sealer111 on both sides along the joint or proxy crack on the prepared substrate.
When sealing cracks, of narrow joints the TS 3000 should not be bonded along the centerline of the tape. A minimum un-bonded width of 20mm is recommended to allow for expansion and contraction.
Place the clean and well aired tape immediately in to the adhesive layer and press well in with a roller. For very wide joints draw the tape suitably in the joint so that a hollow is formed.
In case of negative water pressure (more than 0.3 bar) back up the membrane with an adequate support, e.g. steel sheet, etc., in particular of joints are subject to large movements.
Note
Colour: Grey
Bulk density: 2.0
Plastic density: 1.85
Disclaimer
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the application are beyond our control.
top
|
